TEVKO, transformadores y subestaciones de potencia

Video

Why a transformer hums: magnetostriction

Duration
33 seconds
Language
Spoken in English
Captions
English captions, switchable from the player
Published
Published November 12, 2026

What is behind this video

A hospital transformer hums even though nothing inside it moves. It is not the current. It is magnetostriction in the steel core. At 60 Hz the laminations stretch on every peak and vibrate 120 times a second. If it suddenly hums louder, the video says to check the voltage.

The hum is not from a spinning part. The magnetic field stretches the steel-core laminations a few microns as it rises and lets them shrink back as it falls. That happens on every peak, positive or negative, so at 60 Hz the core vibrates 120 times a second. That tiny motion is what you hear.

The lamination stretches with the magnitude of the flux, not with its polarity. It lengthens on the positive peak and again on the negative peak, twice per cycle of the supply. On a 60 Hz system that produces 120 vibrations a second. The fundamental tone of the core hum is therefore twice the power frequency.

More flux produces more noise. If the unit suddenly hums louder, the video says to check the voltage it is running at. A change in level alone is not enough to declare an internal fault; it is a signal to verify the applied voltage, not a complete diagnosis of the asset.

The references behind what the video says are: New Scientist, The Last Word (120 Hz hum on a 60 Hz system); AIP Advances 7, 056681 (core noise depends on induction).

This piece is animation and typography: it does not show TEVKO personnel. The figures are the ones in the script and can be checked against this page and the linked pages.

Transcript — English audio

Why does a hospital's transformer hum if not a single part inside it moves? It's not the current.

It's the steel core. When the magnetic field rises, the laminations stretch a few microns; when it drops, they shrink back.

Like a rubber band you stretch and release, nonstop. It stretches on every peak, positive or negative.

So at 60 Hz, it vibrates 120 times a second. But watch out: more flux, more noise.

If it suddenly hums louder, check the voltage. So it's not the electricity humming.

It's the steel. Does yours sound different?

Comment HUM and we'll tell you what to check.

The same captions ship as a WebVTT track inside the player. The spoken close invites a comment on the network where the video was posted. On this page the contact is ventas@tevko.com and the phone +52 33 2101 7241.

Questions this video answers

Why does a transformer hum if it has no moving parts?

The hum is not from a spinning part. The magnetic field stretches the steel-core laminations a few microns as it rises and lets them shrink back as it falls. That happens on every peak, positive or negative, so at 60 Hz the core vibrates 120 times a second. That tiny motion is what you hear.

Why is the hum at 120 Hz and not at 60 Hz?

The lamination stretches with the magnitude of the flux, not with its polarity. It lengthens on the positive peak and again on the negative peak, twice per cycle of the supply. On a 60 Hz system that produces 120 vibrations a second. The fundamental tone of the core hum is therefore twice the power frequency.

What should you check if the transformer suddenly hums louder?

More flux produces more noise. If the unit suddenly hums louder, the video says to check the voltage it is running at. A change in level alone is not enough to declare an internal fault; it is a signal to verify the applied voltage, not a complete diagnosis of the asset.

Related pages

Technical content reviewed by TEVKO Technical Management · last reviewed: November 12, 2026

Request a technical assessment

Write to our sales inbox with the following and we will tell you what the next step is:

  • The nameplate: rating, voltage, make and serial number.
  • The location of the installation.
  • The problem the unit presents, or the event that occurred.
ventas@tevko.com